Description
A safe home without complicated installation: Meross CS11-EU smoke and carbon monoxide detector
The Meross CS11-EU smoke and carbon monoxide detector combines photoelectric smoke detection and electrochemical CO detection to give a quick warning in case of possible dangers. The two sensors working together help to notice both smoke and carbon monoxide early and reduce false alarms. The built-in CR123A lithium power source lasts up to 10 years, the compact white housing blends unnoticed into any interior, and compliance with the EN14604 and EN50291 standards confirms its performance.
Main features
- Dual-sensor detection the photoelectric smoke sensor and the electrochemical CO sensor work together to respond to dangers early.
- 85 dB alarm from 3 m a loud signal helps to direct attention immediately when an alarm occurs.
- Fewer false alarms detects both fast and slowly developing fires to ensure a more accurate response.
- Three-colour LED green for ready, yellow for low battery or fault, red for alarm or test mode.
- Up to 10 years of power the built-in 3 V CR123A lithium battery is maintenance-free and does not need replacing.
- Certificates meets the requirements of EN14604 for smoke detection and EN50291 for CO detection.
- Easy installation a cable-free solution with a mounting plate and the screws included, test and silence for about 10 minutes.
Immediate response to danger
The device meets the EN14604 and EN50291 standards, which confirms the quality of detection. When the CO level becomes dangerous, the alarm activates automatically. For example, at 300 ppm the alarm normally sounds in less than 3 minutes. The loud 85 dB signal is clearly audible and helps to draw attention quickly.
Reliability and accuracy
When both smoke and carbon monoxide are detected, the detector first signals the smoke and then the CO, so that the situation is easy to understand. The system distinguishes the detection of fast and slow fires, which helps reduce unnecessary alarms.
Easy installation without cables
Power is provided by the built-in CR123A 3 V lithium battery, with a service life of up to 10 years. Installation is straightforward and normally takes only a few minutes. Fix the mounting plate to the ceiling or wall, place the detector on the plate and the device is ready for use. The help of an electrician is not needed.
Intuitive light signalling
The detector has a three-colour LED for quickly identifying the status. Green means ready, yellow signals a low battery or a fault, and red indicates an alarm or test mode. With one press of a button you can start a test or silence the alarm for about 10 minutes.
Carefully thought-out design
The light, low-profile white housing blends into the room and is compact even in smaller homes. The exterior look is modest so that the device does not draw too much attention.
A discreet look for any interior
The round shape and neutral tone suit both modern and classic interior design. The air vents and the placement of the sensors are optimised to ensure sensitive and stable detection in everyday use.
Use, compatibility and maintenance
The device works independently and does not need a Wi-Fi network or a mobile app. The alarm is given with the built-in siren and LED lights. Thanks to the cable-free power it is suitable for use in homes, summer cottages and garages, where a quick warning is important without the need for special installation.
The set includes all the fixing parts needed for installation. The device is suitable for common areas and bedrooms. Avoid installing it in places where the movement of smoke or gas may be obstructed or where there is a strong air flow, for example right next to ventilation openings or ceiling fans.
For maintenance we recommend doing a regular test once a month. The battery is built in and is not replaceable. If the battery level is low or a fault occurs, the device signals it with a yellow LED and a sound signal. If necessary, clean the outer surface of the detector with a dry cloth and do not cover or paint the housing.
Installation and use step by step
Choose a suitable place on the ceiling or wall, away from direct air flows. Fix the included mounting plate with screws, then place the detector on the plate until it locks firmly. Switch the device to operating mode and run a trial alarm with the test button to make sure it is in working order. The LED indicators help to check the status quickly, and the silence function mutes the alarm for about 10 minutes if needed.
Included in the set
- Smoke and carbon monoxide detector Meross CS11-EU
- Mounting plate
- Screws and wall plugs
- User manual
Choose a dual-sensor solution with a long service life
The Meross CS11-EU combines the accurate detection of a double sensor, a service life of up to 10 years and easy installation. The EN14604 and EN50291 certificates confirm compliance with important requirements, and the loud alarm signal helps to react quickly to a risk. If you need a reliable, low-maintenance detector for your home or summer cottage, this is a practical choice.

Reviews
There are no reviews yet.