Description
Undermount stainless steel sink BLANCO SUPRA 340-U
The undermount stainless steel sink BLANCO SUPRA 340-U is fixed from below to the worktop cut-out, with its rim hidden under the worktop. The sink has a brushed finish and measures 370 × 430 mm outside and 184 mm high. It has one bowl with corners rounded to a 60 mm radius. SUPRA bowls can be combined into a main and an additional bowl.
Installing under the worktop
The sink suits only a worktop of dense, continuous material, such as natural stone, glass or a composite. The worktop cut-out is 400 × 340 mm (tolerance +2/−1 mm) with corners rounded to a 60 mm radius. The supplied screw fixings need a worktop at least 18 mm thick. For a thinner worktop of at least 10 mm, separately sold fixing studs are glued to the underside of the worktop with epoxy.
For the screw fixings, four holes 5 mm in diameter and 13 mm deep are drilled into the underside of the worktop, 22 mm from the cut-out edge. The contact surfaces are cleaned with isopropanol, silicone is applied to the sink rim, the sink is lifted up against the worktop and the fixings are tightened with a PZ 2 screwdriver. The silicone is left to cure for 24 hours before the sink is used. The tap goes into the worktop through a 35 mm hole whose centre is 60 mm from the cut-out edge. In the base cabinet the drain outlet sits 285 mm below the top of the worktop.
Bowl, drain and overflow
The 3½-inch drain opening holds a hand-operated basket strainer, and the overflow opening sits at the top of the rear wall of the bowl. The space-saving pipe of the supplied waste and overflow set takes the drain towards the back of the cabinet and leaves room under the sink, which is why BLANCO recommends it with a pull-out waste sorter.
Stainless steel and surface finish
The SUPRA 340-U is made of 18/10 stainless steel, which contains 18% chromium and 10% nickel. Together with oxygen, chromium forms a thin, invisible protective layer that renews itself. That is why the first fine scratches on a new sink are normal and become less visible as the layer renews.
The brushed surface does not tarnish or change colour when a hot pot is put on it or the sun shines on it for a long time. Small orange spots that appear on the surface come from other rusting objects or iron and rust particles from the water pipes, and they wipe off with a soft sponge.
Stainless steel sink care
For daily cleaning put a little washing-up liquid on the soft side of a sponge and clean the surface along the brushing direction, as circular movements can permanently change the brushed surface. Then rinse the sink and rub it dry with a microfibre cloth so that no small limescale spots remain. To remove limescale, dilute vinegar essence with water 1:10 or use a descaler.
Once a month clean the sink more thoroughly with a stainless steel cleaner: apply a hazelnut-sized amount with a sponge and polish along the brushing direction. To clean the basket strainer, put a level teaspoon of dishwasher powder on the closed strainer, pour over about 250 ml of boiling water, leave it to work, brush and rinse.
Do not use abrasive cleaners or hypochlorite bleach, silver cleaning baths, cleaners containing chlorine or hydrochloric acid, prickly brushes, the scouring side of a sponge or steel wool, and do not leave strong salt solutions on the surface for long.
In the box
- Kitchen sink BLANCO SUPRA 340-U, 1 pc
- Waste and overflow set with space-saving pipe
- 3½″ basket strainer, opened by hand
- Fixing kit
Needed separately
- One trap connects the waste set to the drain: the trap BLANCO 137267 has a 1½″ connection, an outlet for a Ø40 or Ø50 mm pipe and a dishwasher connection.
- With a waste sorter in the sink cabinet, the flat trap BLANCO 137287 with a Ø50 mm outlet and two appliance connections fits instead.
- The kitchen tap is also bought separately.





Reviews
There are no reviews yet.