Description
Inset stainless steel sink BLANCO ETAGON 700-IF
The inset stainless steel sink BLANCO ETAGON 700-IF sits in the worktop cut-out with its rim resting on the worktop. IF stands for the flat rim: the sink looks almost level with the worktop and can also be flush-mounted, with the rim on the same plane as the worktop. The finish is satin polish, the outer size is 740 × 440 mm and the height 199 mm. A step moulded into one side of the bowl creates a second working level above the bowl.
Installation on or flush with the worktop
For inset installation the cut-out is 730 × 430 mm with a tolerance of +2/−1 mm and a corner radius of 15 mm. Installed this way the sink also suits a laminate worktop, as well as compact laminate, stone, glass, stainless steel and composite worktops. The sealing area is cleaned with isopropanol before sealing with silicone, and the sink should not be used for 24 hours after installation.
For flush mounting, a rebate of 742 × 442 mm, 1.5–2 mm deep with 13 mm corner radii is milled around the cut-out, leaving a 1 mm gap between the rim and the worktop. Only a water-repellent worktop suits this, such as granite, glass, artificial stone or mineral material. BLANCO recommends having flush mounting done by a specialist.
The sink is fixed with the supplied clamps, which suit worktops 28–34 mm and 34–40 mm thick. The kitchen tap goes into a 35 mm hole in the worktop, and in a laminate worktop BLANCO recommends sealing the tap hole with flexible sealing tape. According to the side-view drawing, the drain outlet is 290 mm below the worktop, and a dishwasher connects to the separately sold trap.
Bowl, drain and overflow
The bowl has a 3½″ InFino basket strainer that is opened and closed by hand. The overflow has a C-shaped cover, so the overflow opening in the bowl wall stays out of sight.
The space-saving pipe of the waste kit runs the drain towards the back of the cabinet and leaves more room under the sink. BLANCO recommends such a kit when a pull-out waste sorter goes under the sink.
Stainless steel and surface finish
The sink is made of 18/10 stainless steel, which contains 18% chromium and 10% nickel. Chromium and oxygen form a thin invisible protective layer that renews itself. The first fine scratches on a new sink are normal, and many of them become less visible within a few days as the layer renews.
The surface has a satin polish. Reddish spots on the surface are rust carried over from other rusty objects or from the water pipes, and they wipe off. Small light marks are usually limescale that collects dirt particles.
Stainless steel sink care
For daily cleaning use the soft side of a sponge and a little washing-up liquid. To avoid marks, wipe the sink after use with a soft cloth and a mild cleaner and dry it. To remove stubborn limescale, use a descaling stainless steel cleaner with a sponge suited to stainless steel.
To clean the basket strainer, put a level teaspoon of dishwasher powder on the closed strainer, pour about 250 ml of boiling water over it and let it work. Then brush the strainer clean and rinse with clean water. Do not use cleaners with chlorine or hydrochloric acid, steel wool, a scraper or the scouring side of a sponge, and do not leave strong salt solutions on the surface for long.
In the box
- Kitchen sink BLANCO ETAGON 700-IF, 1 pc
- 2 stainless steel ETAGON rails
- Waste and overflow kit with space-saving pipe
- 3½″ InFino basket strainer
- Fixing kit
Needed separately
One trap is needed to connect the sink to the drain. Kitchen sink trap BLANCO 137267 has a 1½″ connection, an outlet for a Ø40 or Ø50 mm drain pipe and a dishwasher connection. With a waste sorter under the sink, the flat kitchen sink trap BLANCO 137287 with a Ø50 mm outlet and two appliance connections fits. The kitchen tap is also bought separately.






Reviews
There are no reviews yet.