Description
4G router with two SIM slots, serial interfaces and GNSS
The Teltonika RUT956 connects to the mobile network through an LTE Cat 4 modem with downloads of up to 150 Mbit/s, and up to 42 Mbit/s on 3G. Supported bands are 4G B1, B3, B7, B8, B20, B28A, B38, B40 and B41, 3G B1 and B8, and 2G B3 and B8. The router has two Mini SIM slots (2FF), and the active SIM switches automatically on weak signal, a reached data limit, roaming or loss of network.
Local network, hotspot and wired backup
The Wi-Fi 4 (IEEE 802.11b/g/n) access point works in the 2.4 GHz band, accepts up to 100 simultaneous connections and supports a hotspot network with a landing page. There are three LAN ports and one WAN port at 10/100 Mbit/s, and the WAN port can be configured as a LAN port. Mobile, wired WAN and Wi-Fi WAN back each other up with automatic failover, and traffic can be balanced across several connections.
Serial interfaces, inputs and outputs
RS232 on a DB9 socket and RS485 on a 6-pin socket connect industrial equipment, which the router serves as a MODBUS RTU master, Serial over IP, modem or NTRIP client. RS485 works in full or half duplex at 300–115200 baud. The 10-pin socket holds a dry input 0–3 V, a galvanically isolated input 0–30 V, an analogue input 0–24 V, an open collector output 30 V / 250 mA and a relay rated 40 V / 4 A. The power connector carries one more digital input and one digital output.
GNSS location and USB port
The GNSS receiver uses GPS, GLONASS, BeiDou, Galileo and QZSS, and coordinates are available in the web interface, by SMS or sent to an RMS or TAVL server. Several geofence zones can be set, and on leaving one the router sends a notification by SMS, e-mail or RMS. The USB 2.0 A port takes an external hard drive, a flash drive, an additional modem or a printer, with FAT, FAT32 and NTFS supported.
RutOS, VPN and remote management
The RutOS operating system is based on OpenWrt, and the router is managed through the web interface or the Teltonika RMS remote management system. VPN options are OpenVPN, IPsec with up to four tunnels, WireGuard, ZeroTier, GRE, PPTP, L2TP and SSTP.
Power and housing
The router runs on 9–30 V DC with reverse polarity protection, and can also be powered by passive PoE through a LAN port. Power consumption is under 2 W at idle and under 7 W at maximum. The aluminium housing with plastic panels measures 110 × 50 × 100 mm, weighs 287 g and is rated IP30. The operating temperature is −40 °C to 75 °C, and the router can be mounted on a DIN rail or placed on a flat surface.
Installation
To fit a SIM card, press the holder button with the SIM needle, pull out the holder, place the SIM card in it and slide it back. Then attach the antennas and connect the power adapter to the socket on the front and to the mains. Connect to the router over Wi-Fi with the SSID and password on the device label, or with an Ethernet cable to a LAN port. To open the web interface go to 192.168.1.1; at first login set a new password of at least 8 characters, after which the configuration wizard starts.
In the box
- 4G router Teltonika RUT956
- 9 W power adapter
- 2 magnetic-mount LTE antennas, SMA connector, 3 m cable
- 2 magnetic-mount Wi-Fi antennas, RP-SMA connector, 1.5 m cable
- Adhesive GNSS antenna, SMA connector, 3 m cable
- RS485 connector block
- Input/output connector block
- Ethernet cable, 1.5 m
- SIM adapter kit
- Quick start guide






Reviews
There are no reviews yet.