Description
BLANCO FONTAS-S II kitchen tap with filter
The kitchen tap with filter BLANCO FONTAS-S II is a 3-in-1 tap with an L-shaped spout, with the body and spout in volcano grey. At the end of the spout there is a pull-out shower: the metal pull-out part and the hose with a nylon coating come out of the spout, and a weight pulls the hose back after use.
Filtered water from a separate handle
The lever on the right mixes cold and warm tap water, and with the rotating handle on the left you open the filtered water. The filtered water travels in its own channel inside the tap and comes out of a separate opening at the end of the spout, so it stays separate from the tap water. For the filtered water, the same tap hole is enough in which the tap itself is installed.
The warm water can be up to 70 °C, the cold water at the filter inlet 4–30 °C, because the water filter system works only with cold water. The filter hose of the tap is connected to the outlet of the filter system and its connection is tightened up to 15 Nm. As an additional option, a water meter with a screen can be installed in front of the filter, and a T-connector on the cold water angle valve. On first use, remove the aerators from the end of the spout, let filtered water run for at least 10 litres and mixed water for at least 20 seconds, then put the aerators back.
Spout, shower and flow rate
The spout reaches 216 mm from the centre of the body and the total height of the tap is 306 mm. At a water mains pressure of 3 bar, the tap delivers 7.7 litres of water per minute. The shower has one spray mode: the aerator at the end of the spout mixes air into the water jet.
Installation and water pressure
The tap is installed in a hole with a diameter of 35 mm in the sink or worktop, and the thickness of the mounting surface can be up to 59 mm. On a stainless steel sink, a stabilising plate holds the tap firmly in place. The flexible connection hoses are 500 mm long and have a ⅜″ nut: the hose with the red marking is connected to the warm water angle valve and the one with the blue marking to the cold water angle valve.
The shower hose is attached under the tap with a click and the weight is put on it. The non-return valve complies with the EN 1717 standard and prevents water from flowing back into the water mains. BLANCO recommends having the tap and the filter system installed by a specialist.
BLANCO FONTAS-S II works at a water mains pressure of 2–8 bar. The high-pressure tap is intended for a kitchen where both cold and warm water come from pipes in the wall. For an open boiler located under the sink, a low-pressure tap (ND) with three hoses is needed. Only a low-pressure tap is suitable to replace a low-pressure tap, because the number of hoses is different.
Finish and sink colour
The tap body is made of brass and its surface has a SILGRANIT-look finish. The colour follows the colours of BLANCO SILGRANIT sinks, so a volcano grey tap is the same colour as a volcano grey BLANCO sink.
Tap care
After use, dry the tap with a microfibre cloth, which can be washed in a washing machine at up to 90 °C. To remove limescale, use a vinegar or citric acid solution or a limescale remover: spray it on the surface, let it work for a moment, wipe over with a damp cloth and dry. Clean with the soft side of a sponge and do not use cleaning agents containing chlorine or the abrasive deep cleaner for granite sinks.
If the jet starts to splash, unscrew the aerator and leave it overnight in vinegar water or a citric acid solution. Keep the shower hose straight, and if it no longer slides smoothly back into the body, apply a little tap grease to it. According to BLANCO, spare parts for taps are available for at least 10 years.
Included
- BLANCO FONTAS-S II kitchen tap with filter (3-in-1) and pull-out shower
- Weight that pulls the shower hose back
- Flexible connection hoses, 500 mm, with ⅜″ nut
- Stabilising plate for installing the tap in a stainless steel sink
- Non-return valve (EN 1717)
Needed separately
To get filtered drinking water, a BLANCO water filter system is needed, connected between the cold water angle valve and the filter hose of the tap. To connect the tap to the water mains, cold and warm water angle valves are needed under the sink. With old water pipes, BLANCO recommends installing a dirt filter between the angle valve and the connection hose, and with high pressure two filters in a row.




Reviews
There are no reviews yet.