Description
Filter kitchen mixer tap BLANCO FONTAS-S II
Filter kitchen mixer tap BLANCO FONTAS-S II is a 3-in-1 tap that delivers both unfiltered mains water and filtered drinking water from one pull-out spout. The colour is tartufo and the spout is L-shaped. A high-pressure (HD) tap suits a kitchen where both cold and hot water pipes come from the wall; an open, unvented boiler under the sink needs a low-pressure (ND) tap.
Filtered water from a separate handle
The lever on the right mixes cold and warm water, the rotary handle on the left opens the filtered water. Filtered water runs through its own channel inside the tap and leaves the spout through its own outlet, so it does not mix with mains water. All three types of water come from one tap, so no extra hole in the worktop is needed for filtered water.
Hot water may be up to 70 °C, and the cold water at the filter inlet 4–30 °C. The filter, a flow meter with display and a T-piece for the cold angle valve are options connected to the tap’s filtered-water hose; the filter head connections are tightened to at most 15 Nm. At first use, run at least 10 l of water from the left handle and then water from the right lever for at least 20 seconds.
Spout, spray and flow rate
The total height of the tap is 306 mm and the spout reaches 216 mm. The flow rate is 7.7 l/min at 3 bar. The spray has one jet mode, and the aerator at the end of the spout adds air to the jet. The metal spray head is connected to a nylon-sheathed hose, which a hose weight pulls back after use. A ceramic disc cartridge controls the flow and temperature.
Installation and water pressure
The tap fits a 35 mm hole, and according to BLANCO’s dimension drawing the mounting surface may be up to 59 mm thick. It connects to the supply with flexible 500 mm connection hoses with a ⅜″ nut. When fitted in a stainless steel sink, the supplied stabilising plate gives the tap extra support. A non-return valve prevents backflow into the mains to EN 1717.
FONTAS-S II is a high-pressure (HD) tap only and works at a supply pressure of 2–8 bar. A high-pressure tap connects with two hoses directly to the cold and hot water pipes, while a low-pressure tap has three hoses, so a high-pressure tap is fitted to a high-pressure connection. For old water pipes, BLANCO recommends the dirt filter 128434 between the angle valve and the tap hose. After installation, let the water run for 10 minutes and check the connections.
Finish and matching sink colour
SILGRANIT-look is a powder coating that fuses with the brass tap body at 200 °C into an even surface. BLANCO makes its SILGRANIT-look taps in the same colours as its SILGRANIT sinks, so a tartufo tap matches a BLANCO sink in the same colour.
Tap care
After use, dry the tap with a microfibre cloth, for example the BLANCO microfibre cloth 126999. Remove limescale with an acetic or citric acid solution or the BLANCO descaler DailyClean+ (526305): the SILGRANIT-look surface tolerates them when you keep to the contact time. Leave chlorine-based cleaners and scouring pads aside when cleaning the tap.
If the aerator is scaled, unscrew it anticlockwise and soak it overnight in vinegar water or citric acid. If the spray hose no longer glides back smoothly, apply tap lubricant to its moving parts. Take care not to kink the hose, as a kink can make it drip. According to BLANCO, spare parts for its taps are available for at least 10 years.
In the box
- Hose weight that pulls the spray hose back
- Flexible connection hoses, 500 mm, with ⅜″ nut
- Stabilising plate for fitting the tap in a stainless steel sink
- Non-return valve (EN 1717)
Needed separately
For filtered drinking water, a BLANCO water filter system is installed under the sink, connected between the cold angle valve and the tap’s filtered-water hose.




Reviews
There are no reviews yet.