Description
Filter kitchen tap BLANCO FONTAS-S II
The filter kitchen tap BLANCO FONTAS-S II gives three kinds of water from one tap: cold, warm and filtered (3-in-1). Mains water and filtered water both come through the same pull-out spray, each from its own outlet. The tap is L-shaped and its finish is satin platinum. As a high-pressure tap (HD), FONTAS-S II is connected to cold and hot water pipes coming from the wall.
Filtered water from its own handle
The tap has a rotary handle on the left for drinking water, while the lever on the right mixes cold and warm water. Filtered water runs through its own channel in the tap and leaves the spray through its own outlet, so it reaches the glass apart from mains water. The existing tap hole is enough for filtered water, because all three kinds of water come from one tap.
The water filter system runs on cold water only, and the cold water at the filter inlet must be 4–30 °C. Hot water entering the tap may be up to 70 °C. At first use, run at least 10 l of filtered water with the left handle, then at least 20 seconds of mains water with the right lever. A flow meter with display and a T-piece for the cold angle valve can be added as options.
Spout, spray and flow rate
The spout reach is 216 mm and the total height 306 mm. The maximum flow rate at 3 bar is 7.7 l/min, and the aerator at the end of the spout mixes air into the jet. The pull-out spray head is metal and the spray hose is nylon-sheathed. A hose weight pulls the spray reliably back to the spout.
Installation and water pressure
The tap fits a 35 mm tap hole and the mounting surface may be up to 59 mm thick. It is connected with flexible connection hoses, 500 mm long with a ⅜″ nut: the red hose to the hot and the blue hose to the cold angle valve. Before connecting the hoses, flush the pipes by letting water run from the angle valves into a bucket.
In a stainless steel sink, a stabilisation plate gives the tap extra support. A non-return valve prevents backflow into the pipework in accordance with EN 1717. Installation needs a PH2 screwdriver and 14, 19 and 22 mm spanners. After installation, open the angle valves and check every connection for leaks.
The tap works at a supply pressure of 2–8 bar. A high-pressure tap (HD) is meant for a kitchen where cold and hot water pipes come from the wall. Where an open boiler under the sink supplies hot water, a low-pressure tap (ND) with three connection hoses is the right choice.
Because the number of hoses differs, a high-pressure tap is always connected to high-pressure connections. For old water pipes, BLANCO recommends fitting a dirt filter between the angle valve and the connection hose.
Finish and sink colour
The tap body is brass with a satin platinum PVD finish. BLANCO recommends the satin platinum tap with composite and ceramic sinks.
Tap care
After use, dry the tap with a microfibre cloth. To remove limescale, use a vinegar or citric acid solution or a descaler: leave it only for the time its instructions allow, then rinse the tap with water. Do not clean the tap with chlorine-based cleaners.
If the aerator is hard with limescale, unscrew it anticlockwise and leave it overnight in vinegar water or citric acid. Keep the spray hose free of kinks, as a kink damages the hose and can make it drip. If the hose no longer glides back smoothly, apply tap grease. According to BLANCO, spare parts for the tap are available for at least 10 years.
In the box
- Kitchen mixer tap BLANCO FONTAS-S II, 1 pc
- Flexible connection hoses, 500 mm, with ⅜″ nut
- Stabilisation plate for fitting the tap in a stainless steel sink
- Hose weight that pulls the spray hose back
Needed separately
Filtering drinking water needs a BLANCO water filter system, whose inlet is connected to the cold angle valve and its outlet to the tap’s filter hose. The filter head connection is tightened to at most 15 Nm.




Reviews
There are no reviews yet.