Description
Inset stainless steel sink BLANCO SOLIS 500-IF/A
The inset stainless steel sink BLANCO SOLIS 500-IF/A has a flat IF rim, so it can rest on the worktop or sit level with it. The surface has a brushed finish, and the sink measures 540 × 500 mm with a height of 194 mm. You open and close the drain with a pop-up button at the back of the sink next to the tap position.
Installation on or flush with the worktop
Installed from above, the sink suits laminate as well as stone, glass, stainless steel and composite worktops. The cut-out is 530 × 490 mm with a tolerance of +2/−1 mm and a corner radius of 15 mm. The flat IF rim makes even an inset sink look almost flush.
Flush installation needs a water-repellent worktop such as granite, glass, artificial stone or mineral material; wood and laminate swell with water. A rebate of 542 × 502 mm, 1.5–2 mm deep with a 13 mm corner radius, is milled around the cut-out, leaving a 1 mm gap between the sink rim and the worktop. BLANCO recommends having flush installation done by a specialist.
The fixing clamps suit worktops 28–34 mm and 34–40 mm thick. The tap hole at the back of the sink is made at the factory. The surfaces are cleaned with isopropanol before sealing, and after sealing with silicone the sink needs 24 hours before use. According to the side view drawing, the drain outlet sits 285 mm below the top of the worktop.
Bowl, drain and overflow
The bowl has a 3½″ InFino basket strainer controlled by the flat PushControl button: one press opens the drain and the next closes it. The overflow is a covered C-overflow in the bowl wall. The space-saving pipe of the waste kit leads the drain towards the back of the cabinet and leaves more room under the sink. BLANCO recommends this pipe when a pull-out waste sorter goes under the sink.
Stainless steel and surface finish
The sink is made of 18/10 stainless steel containing 18% chromium and 10% nickel. With oxygen, the chromium forms a thin, invisible protective layer that renews itself. The first fine scratches on a new sink are normal and become less visible as the layer renews.
The brushed finish is one of BLANCO’s three classic stainless steel finishes and the most chosen of them. Reddish dots on the surface are rust carried over from other rusty objects or water pipes, and they wipe off.
Stainless steel sink care
For daily cleaning, put washing-up liquid on the soft side of a sponge and wipe in the brushing direction, without circular movements. Then rinse the sink and dry it with a microfibre cloth, such as BLANCO cloth 126999. For limescale, use vinegar essence diluted 1:10 with water or BLANCO DailyClean+.
Once a month, deep clean with BLANCO DeepClean Stainless Steel 526306: apply a hazelnut-sized amount with a sponge and polish in the brushing direction. To clean the basket strainer, put a level teaspoon of dishwasher powder on the closed strainer, pour about 250 ml of boiling water over it, let it work, brush it clean and rinse. Do not use abrasive cleaners, hypochlorite bleach, silver cleaning baths, cleaners with chlorine or hydrochloric acid, scratchy sponges or steel wool.
In the box
- Waste and overflow kit with space-saving pipe
- 3½″ InFino basket strainer and push-to-open pop-up button
- Fixing kit
Needed separately
One trap is needed to connect the sink to the drain. Kitchen sink trap BLANCO 137267 connects the waste kit to a Ø40 or Ø50 mm drain pipe and has a dishwasher connection. With a waste sorter under the sink, the flat trap BLANCO 137287 with a Ø50 mm outlet and two appliance connections fits instead. The kitchen tap is also bought separately.






Reviews
There are no reviews yet.