Description
Inset stainless steel sink BLANCO CLARON 500-IF/A
The inset stainless steel sink BLANCO CLARON 500-IF/A is a single-bowl sink with a flat IF rim that rests on the worktop. The same sink can also be fitted flush, with the rim level with the worktop. It is stainless steel with a satin polish finish, the outer size is 560 × 510 mm and the height 199 mm.
The tap sits on the ledge at the back of the sink, where the tap hole is made at the factory. BLANCO has given the tap mounting at the back of the sink additional stabilisation.
Inset or flush installation
The IF rim means one model suits two installation methods. For inset installation the cut-out is 540 × 490 mm, tolerance +2/−1 mm, corner radius 0–15 mm. Installed this way the sink suits almost any worktop: laminate, compact laminate, stone, glass, stainless steel and composite. The rim is sealed to the worktop with silicone.
For flush installation a rebate of 562 × 512 mm, 1.5–2 mm deep, is cut around the cut-out, with a tolerance of +1/−1 mm and a corner radius of 11 mm. A 1 mm gap remains between the sink rim and the rebate edge. Flush mounting needs a water-repellent worktop such as granite, glass, artificial stone, glass ceramic or a mineral composite, because wood and laminate swell on contact with water. BLANCO recommends having a flush sink fitted by a specialist.
The supplied clamps suit worktops 28–34 mm and 34–40 mm thick. According to the drawing, the waste pipe connection is 290 mm below the top of the worktop. A dishwasher is connected through the separately sold trap.
Bowl, waste and overflow
The bowl has BLANCO’s InFino drain system: a 3½″ InFino basket strainer and a covered overflow. The drain opens and closes with the flat PushControl button on the ledge at the back. The bowl corners have a 10 mm radius and the bowl base has no visible pressed pattern.
The supplied waste pipe saves space: it routes the drain towards the back of the cabinet and leaves room under the sink. BLANCO recommends this pipe when a pull-out waste sorter goes under the sink.
Stainless steel and surface finish
The sink is made of 18/10 stainless steel, containing 18% chromium and 10% nickel. Chromium forms a thin, invisible protective layer with oxygen that renews itself. The first fine scratches on a new sink are normal and become less visible within a few days as the layer renews.
The satin polish gives the steel a silky sheen. With its flat IF rim the stainless sink looks almost flush even when fitted as an inset sink. Reddish spots on the surface are rust carried over from other rusty objects or the water pipes, and they wipe off.
Stainless steel sink care
For daily cleaning use the soft side of a sponge and a little washing-up liquid. Wipe along the grain, then rinse and dry the sink with a soft cloth so that no limescale marks remain. To remove limescale, use vinegar essence diluted 1:10 with water or a descaler. Once a month you can clean the surface with a stainless steel cleaner: apply a hazelnut-sized amount and rub it in along the grain.
To clean the basket strainer, put a level teaspoon of dishwasher powder on the closed strainer and pour about 250 ml of boiling water over it. Let it work, brush the strainer clean and rinse with clean water. A soft sponge and a cleaner free of chlorine and hydrochloric acid protect the surface; abrasives, hypochlorite bleach, silver cleaners, steel wool, scratchy sponges and strong salt solutions left on for a long time damage it.
In the box
- Kitchen sink BLANCO CLARON 500-IF/A, 1 pc
- Waste and overflow set with space-saving pipe
- 3½″ InFino basket strainer and push pop-up button
- Fixing kit
Needed separately
One trap is needed to connect the sink to the drain. Kitchen sink trap BLANCO 137267 connects the waste set to a Ø40 or Ø50 mm drain pipe and has a dishwasher connection. If a waste sorter goes in the sink cabinet, the flat kitchen sink trap BLANCO 137287 fits, with a Ø50 mm outlet and two appliance connections. The kitchen tap is bought separately.







Reviews
There are no reviews yet.